પરિચય
This manual provides detailed instructions for the setup, operation, and maintenance of your Sovol SH01 Filament Dryer and Sovol Tri-Color Silk PLA Filament. Adhering to these guidelines will help ensure optimal performance and longevity of your products, leading to successful 3D printing outcomes.
ઉત્પાદન ઓવરview
Sovol SH01 Filament Dryer
The Sovol SH01 Filament Dryer is designed to maintain optimal filament conditions by actively drying and storing your 3D printing filaments. It features a built-in fan for even heating, a display for real-time temperature and humidity, and a robust sealing mechanism for effective moisture control.
Image: Sovol SH01 Filament Dryer showcasing its large capacity, temperature and humidity display, excellent sealing function, and built-in fan.
મુખ્ય લાક્ષણિકતાઓમાં શામેલ છે:
- મોટી ક્ષમતા: Accommodates various filament spool sizes.
- Temperature & Humidity Display: Provides real-time environmental data inside the dryer.
- Excellent Sealing Function: Minimizes moisture re-entry.
- Built-in Fan: Ensures uniform heat distribution for efficient drying.
Sovol Tri-Color Silk PLA Filament
The Sovol Tri-Color Silk PLA Filament is a unique 3D printing material that co-extrudes three distinct colors (Gold, Silver, Bronze) along its length. This allows for dynamic color shifts in printed objects, even small ones, by simply rotating the print orientation. It is manufactured from imported PLA raw material, designed for smooth printing with minimal issues.
Image: A spool of Sovol Tri-Color Silk PLA Filament alongside three small vases demonstrating the gold, silver, and bronze color transitions.
મુખ્ય લાક્ષણિકતાઓમાં શામેલ છે:
- Tri-Color Co-extrusion: Gold, Silver, and Bronze colors are present throughout the filament.
- Imported PLA Raw Material: Ensures quality and a pearlescent, shiny surface finish.
- Easy to Print: Designed for smooth extrusion with a diameter tolerance of +/- 0.03mm, reducing issues like jamming, bubbles, and tangles.
- Eco Packaging: Utilizes paper spools and boxes, vacuum-packed with desiccant.
સેટઅપ સૂચનાઓ
Sovol SH01 Filament Dryer Setup
- પ્લેસમેન્ટ: Place the filament dryer on a stable, level surface near your 3D printer.
- Loading Filament: Open the dryer lid. Place your filament spool(s) inside the dryer. The SH01 can accommodate one large spool or two smaller spools.
- ડેસીકન્ટ પ્લેસમેન્ટ: For enhanced drying and storage, place up to four small bags of desiccant (not included, typically found in filament packaging) inside the dryer, as shown in the diagram.
- Filament Routing: Route the filament through the designated outlet hole on the dryer lid. Ensure the filament passes through the PTFE seal for smooth feeding and to maintain the internal environment.
- પાવર કનેક્શન: Connect the power adapter to the dryer and plug it into a suitable power outlet.
છબી: આંતરિક view of the Sovol SH01 Filament Dryer, indicating the area for desiccant packs to be placed for long-term storage.
Image: The Sovol SH01 Filament Dryer showing filament being fed out through the PTFE sealed outlet, ready for connection to a 3D printer.
Sovol Tri-Color Silk PLA Filament Preparation
Before printing, ensure the filament is properly dried using the SH01 Filament Dryer. Once dried, load the filament into your 3D printer according to your printer's specific instructions. The filament is designed for universal compatibility with most FDM 3D printers.
Image: Sovol Tri-Color Silk PLA Filament spool mounted on a 3D printer, with the filament feeding smoothly into the extruder, illustrating the "No Jam and Less Tangled" feature.
ઓપરેટિંગ સૂચનાઓ
Sovol SH01 Filament Dryer Operation
Follow these steps to operate the filament dryer:
- પાવર ચાલુ: પાવર બટન દબાવો (Ⓟ) to turn on the device. The display will show the current temperature and humidity.
- તાપમાન સેટ કરો: Press the 'M' button to enter temperature setting mode. Use the up (▲) અને ડાઉન (▼) buttons to adjust the temperature between 40-50℃. Recommended temperatures for common filaments are:
- PLA/Wood: 40-50℃
- PETG/TPU/PVE: 45-50℃
- ABS/PC: 50℃
- Set Drying Time: Press the 'M' button again to enter drying time setting mode. Use the up (▲) અને ડાઉન (▼) buttons to set the drying time between 6-12 hours.
- સૂકવવાનું શરૂ કરો: Press the 'M' button once more to confirm settings and enter working mode. The display will show "WORK" and the drying process will begin.
- Filament Feeding during Printing: The dryer can be used to feed filament directly to your 3D printer while drying.
- Bowden Extruder: For printers with a Bowden extruder, route the filament from the dryer to the Bowden tube.
- Direct Drive Extruder: For printers with a direct drive extruder, route the filament directly from the dryer to the extruder.
Image: Close-up of the Sovol SH01 Filament Dryer's control panel, illustrating the steps for powering on, setting temperature, setting drying time, and entering working mode.
Image: Diagrams illustrating the recommended filament port and direction for 3D printers equipped with either a Bowden or Direct Drive extruder, when used with the SH01 dryer.
Sovol Tri-Color Silk PLA Filament Printing Guidelines
For optimal results with Sovol Tri-Color Silk PLA Filament, consider the following general printing parameters. Always refer to your 3D printer's specific recommendations and perform calibration prints.
- નોઝલ તાપમાન: 200-220℃
- Bed Temperature: 45-60℃
- પ્રિન્ટીંગ ઝડપ: 40-70mm/s
- Retraction (Bowden): 4-6 મીમી
- Retraction (Direct Drive): 0.5-1 મીમી
The unique tri-color effect can be influenced by the orientation of your print. Experiment with different rotations of your model on the build plate to achieve varied color transitions.
જાળવણી
Sovol SH01 Filament Dryer Maintenance
- સફાઈ: Periodically wipe the exterior of the dryer with a soft, dry cloth. Ensure the device is unplugged before cleaning. Do not use abrasive cleaners or immerse the unit in water.
- ડેસીકન્ટ રિપ્લેસમેન્ટ: If using desiccant packs, monitor their condition and replace them when they are saturated (indicated by color change, if applicable).
- લાંબા ગાળાનો સંગ્રહ: When not in use, ensure the dryer lid is securely closed to maintain the internal environment, especially if desiccant is present.
Sovol Tri-Color Silk PLA Filament Storage
- Post-Printing Storage: After printing, secure the end of the filament in the winding hole on the spool to prevent tangling.
- ભેજ સંરક્ષણ: Store unused filament in its original vacuum-sealed bag with desiccant, or within the Sovol SH01 Filament Dryer, to protect it from moisture absorption.
Image: Close-up of the Sovol PLA filament spool, highlighting the winding hole designed to secure the filament end and prevent tangles during storage.
મુશ્કેલીનિવારણ
This section addresses common issues related to filament quality and printing. The Sovol SH01 Filament Dryer and Tri-Color Silk PLA Filament are designed to minimize these problems.
| અંક | સંભવિત કારણ | ઉકેલ |
|---|---|---|
| નોઝલ ક્લોગિંગ | Moisture in filament, incorrect printing temperature, dust. | Ensure filament is dry using the SH01 dryer. Verify nozzle temperature is within 200-220℃. Clean the nozzle. |
| Print Warping/Poor Adhesion | Moisture in filament, incorrect bed temperature, uncalibrated bed. | Dry filament with SH01. Set bed temperature to 45-60℃. Ensure proper first layer adhesion and bed leveling. |
| Filament Tangling | Improper storage, loose filament end. | Always secure the filament end in the spool's winding hole after use. Store spools neatly. |
| Inconsistent Extrusion/Bubbles | Moisture in filament. | Dry filament thoroughly using the SH01 dryer. |
Image: A 3D printer actively printing a vase, demonstrating smooth operation without nozzle clogging or warping, attributed to superior filament adhesion.
વિશિષ્ટતાઓ
Sovol SH01 Filament Dryer
- બ્રાન્ડ: Sovol
- મોડલ: SH01
- વસ્તુનું વજન: આશરે 2.2 પાઉન્ડ (1 કિગ્રા)
- સામગ્રી: પ્લાસ્ટિક
- તાપમાન શ્રેણી: 40-50℃ (Adjustable)
- સૂકવવાનો સમય: 6-12 hours (Adjustable)
- પ્રદર્શન: Real-time temperature and humidity
Sovol Tri-Color Silk PLA Filament
- બ્રાન્ડ: Sovol
- સામગ્રીનો પ્રકાર: પોલિલેક્ટિક એસિડ (PLA)
- રંગ: Tri-color (Gold, Silver, Bronze)
- વસ્તુનું વજન: ૧ કિલોગ્રામ (૨.૨ પાઉન્ડ)
- આઇટમ વ્યાસ: 1.75 મીમી
- Diameter Tolerance: +/- 0.03 મીમી
- Recommended Nozzle Temp: 200-220℃
- Recommended Bed Temp: 45-60℃
- Recommended Printing Speed: 40-70mm/s
વોરંટી અને આધાર
Sovol offers a Life-time Guarantee for the Tri-Color Silk PLA filament. If the filament does not perform as expected, please contact Sovol customer support for assistance. For any questions or support regarding either the SH01 Filament Dryer or the Tri-Color Silk PLA Filament, please refer to the official Sovol webસાઇટ અથવા તેમના ગ્રાહક સેવા વિભાગનો સંપર્ક કરો.
You can visit the Sovol Store for more information: Sovol Store on Amazon
