FlyRobo BM730 3-in-1 Voltage Current Power Meter User Manual

પરિચય

The FlyRobo BM730 is a compact 3-in-1 digital meter designed to measure DC voltage, current, and power simultaneously. It features a clear 4-digit LED display for easy reading and is suitable for monitoring battery levels, solar panels, and other DC systems. This manual provides essential information for safe and effective operation.

સલામતી માહિતી

• Always ensure proper wiring connections before applying power.
• ઉલ્લેખિત વોલ્યુમ કરતાં વધી જશો નહીંtage (0-100V DC) and current (10A) limits.
• જીવંત સર્કિટ્સ સાથે સંપર્ક ટાળો.
• This device is intended for DC circuits only.
• બાળકોની પહોંચથી દૂર રાખો.

પેકેજ સામગ્રી

ખાતરી કરો કે બધી વસ્તુઓ હાજર છે:

• 1x FlyRobo BM730 3-in-1 Voltage Current Power Meter
• 1x Wiring Harness for Power Supply (Thin Red/Black Wires)
• 1x Wiring Harness for Current Measurement (Thick Red/Black Wires)

Image: The BM730 meter shown with its two included wiring harnesses. One harness has thin red and black wires for power, and the other has thicker red and black wires for current measurement.

ઉત્પાદન ઓવરview

The BM730 meter features a multi-color LED display and control buttons for operation.

છબી: ટોચ view showing the digital display for voltage (V), current (A), and power (W), along with control buttons (Up, M, Down, R). Bottom view shows the circuit board with connection terminals.

પ્રદર્શિત સૂચકાંકો:

• V (Volts): Red display, indicates DC voltage.
• એ (Ampઇરેસ): Green display, indicates DC current.
• W (Watts): Blue display, indicates DC power.

નિયંત્રણ બટનો:

• ઉપર તીર: Used for navigation or increasing મૂલ્યો.
• M (મોડ): Used to switch display modes or confirm settings.
• ડાઉન એરો: Used for navigation or decreasing મૂલ્યો.
• R (Reset): Used to reset readings or settings.

વિશિષ્ટતાઓ

• ભાગtage રેન્જ: 0V થી 100V DC
• વર્તમાન શ્રેણી: 0A to 10A DC
• પાવર રેન્જ: 0W to 1000W (calculated from V*A)
• પ્રદર્શન: 4-Digit LED (Red for V, Green for A, Blue for W)
• પરિમાણો (L x W x H): 80mm x 41mm x 26mm
• માપન પ્રકાર: Ammeter, Voltmeter, Wattmeter
• પાવર સ્ત્રોત: Battery Powered (self-powered from measured circuit or external supply)

સેટઅપ અને ઇન્સ્ટોલેશન

Proper wiring is critical for the safe and accurate operation of the BM730 meter. Refer to the diagram below for connection details.

વાયરિંગ કનેક્શન્સ:

1. Power Supply for Meter (Thin Red/Black Wires):

   Connect the thin red wire to the positive (+) terminal of your DC power source (0-100V).

   Connect the thin black wire to the negative (-) terminal of your DC power source.

   Note: The meter can be self-powered from the circuit it is measuring, or powered by a separate supply within its voltage શ્રેણી.

2. Current Measurement (Thick Red/Black Wires):

   The thick red wire (IN+) and thick black wire (OUT-) are for current measurement. These wires must be connected in series with the load you wish to measure.

   Connect the thick red wire (IN+) to the positive side of the load.

   Connect the thick black wire (OUT-) to the negative side of the load, completing the circuit back to the power source.

   મહત્વપૂર્ણ: Do not connect the thick current wires directly across the power source; this will short the circuit and damage the meter or power source.

શૉર્ટ સર્કિટને રોકવા માટે તમામ કનેક્શન સુરક્ષિત અને ઇન્સ્યુલેટેડ છે તેની ખાતરી કરો.

ઓપરેટિંગ સૂચનાઓ

1. પાવર ચાલુ: Once correctly wired, apply power to the circuit. The meter's display will illuminate, showing voltage, current, and power readings.
2. રીડિંગ ડિસ્પ્લે:

   The top red display shows voltage વોલ્ટમાં (V).

   The middle green display shows current in Ampઇરેસ (એ).

   The bottom blue display shows power in Watts (W).

3. બટન કાર્યો:

   The buttons (Up, M, Down, R) are typically used for fine adjustment, calibration, or alarm settings. Refer to specific advanced usage guides if available for detailed button functionalities. For basic operation, the meter displays readings automatically.
4. ઓવરવોલtage/Overcurrent Alarm: The meter supports an overvoltage and overcurrent sound alarm function. If the measured values exceed preset thresholds, an audible alarm may sound.

જાળવણી

• Keep the meter clean and dry. Use a soft, dry cloth to wipe the display and casing.
• Avoid exposing the meter to extreme temperatures, humidity, or corrosive environments.
• સી ખોલવાનો પ્રયાસ કરશો નહીંasing or modify the internal circuitry, as this will void any warranty and may cause damage.
• ઉપયોગમાં ન હોય ત્યારે સુરક્ષિત જગ્યાએ સ્ટોર કરો.

મુશ્કેલીનિવારણ

મીટર ચાલુ થતું નથી:

Check the thin red and black power supply wires. Ensure they are correctly connected to a DC power source within the 0-100V range. Verify the power source is active.

ભાગtage displays, but current/power shows 0:

Ensure the thick red (IN+) and black (OUT-) current measurement wires are correctly connected in series with the load. The load must be drawing current for a reading to appear.

અચોક્કસ વાંચન:

Verify all connections are secure and free from corrosion. Ensure the meter is operating within its specified voltage અને વર્તમાન રેન્જ.

Audible alarm sounds:

This indicates an overvoltage or overcurrent condition. Check your circuit for excessive voltage or current draw and adjust as necessary.

વોરંટી અને આધાર

For warranty information or technical support, please contact FlyRobo directly. Refer to your purchase documentation for specific warranty terms.

ઉત્પાદક સંપર્ક માહિતી: flyroboofficial@gmail.com