D149H181 Ed.08
AKO-D14918
આ AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality
ચેતવણીઓ
-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.
વર્ણન
- એલઇડી કોમ
- રેકોર્ડ કી
- EXTERNAL POWER CONNECTOR
- READ KEY
- એલઇડી ચાલુ
- CONNECTOR CABLE
સુસંગતતા
Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.
Connecting incompatible devices can permanently damage the key.
વાયરિંગ
- મહત્વપૂર્ણ: Pay attention to the orientation of the connector.
- એકો-80018
(વૈકલ્પિક) - AKO-D14918
વીજ પુરવઠો
-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (એકો-80018 અથવા સમકક્ષ).
ઓપરેશન
મહત્વપૂર્ણ: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.
RECORD key
Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.
READ key
It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.
એલઇડી ચાલુ
Steady or flashing: Indicates that the key is connected to the controller.
એલઇડી કોમ
સ્થિર: Indicates an error in the transmission/reception of data
ઝડપી ફ્લેશિંગ: Indicates transmission/reception of data in progress. At the end of the transmission એલઇડી કોમ બંધ થઈ જશે.
ધીમી ફ્લેશિંગ: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.
નોંધ: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.
મહત્વપૂર્ણ: ક્યારેય નહીં disconnect the programming key during data transmission.
ટેકનિકલ વિશિષ્ટતાઓ
Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
પુરવઠો ભાગtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
પર્યાવરણીય વિશિષ્ટતાઓ:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC
એકો ઈલેક્ટ્રોમેકૅનિકા, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | España
35D149181 REV.07 2025
અમારી ટેકનિકલ શીટ્સમાં વર્ણવેલ સામગ્રીઓથી સહેજ અલગ હોઈ શકે તેવી સામગ્રી સપ્લાય કરવાનો અધિકાર અમે અનામત રાખીએ છીએ.
અપડેટ કરેલી માહિતી અમારા પર ઉપલબ્ધ છે webસાઇટ
દસ્તાવેજો / સંસાધનો
 |
AKO D14918 Programming Key [પીડીએફ] સૂચના માર્ગદર્શિકા AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key |