Livex Lighting 2161-02 Outdoor Wall Lantern Instruction Manual

મહત્વપૂર્ણ સલામતી માહિતી

Please read these instructions carefully before installing or operating your Livex Lighting 2161-02 Outdoor Wall Lantern. Retain this manual for future reference.

ચેતવણી! ફ્યુઝ અથવા સર્કિટ બ્રેકર પર પાવર બંધ કરો.

This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unsure about any part of the installation, consult a qualified electrician.

દરખાસ્ત 65 ચેતવણી: આ ઉત્પાદનમાં કેન્સર, જન્મજાત ખામી અથવા અન્ય પ્રજનન નુકસાન પહોંચાડવા માટે કેલિફોર્નિયા રાજ્યમાં જાણીતા રસાયણો હોઈ શકે છે.

ઉત્પાદન ઓવરview

The Livex Lighting 2161-02 is a traditional outdoor wall lantern designed to provide illumination and enhance the aesthetic of your outdoor spaces. It features a polished brass finish and clear beveled glass shades, offering a classic and durable lighting solution.

Image: The Livex Lighting 2161-02 Outdoor Wall Lantern, showcasing its polished brass finish and clear beveled glass panels.

પેકેજ સામગ્રી

ઇન્સ્ટોલેશન શરૂ કરતા પહેલા ખાતરી કરો કે બધા ઘટકો હાજર છે:

• Fixture body with pre-assembled wiring
• ક્રોસબાર
• માઉન્ટિંગ સ્ક્રૂ
• વાયર નટ્સ
• Glass shades (pre-installed or separate)
• Candle sleeve (if applicable)
• હેક્સ નટ્સ

સેટઅપ અને ઇન્સ્ટોલેશન

Before starting, ensure the power is turned off at the circuit breaker or fuse box to prevent electrical shock.

ફિક્સ્ચર માઉન્ટ કરવાનું

1. Shut off the power at the circuit breaker and remove any old fixture, including the crossbar.
2. Carefully unpack the new fixture and lay out all parts on a clean, clear surface. Take care not to lose any small parts necessary for installation.
3. Attach the mounting screw part way into the side hole of the crossbar. Then, lock it securely with a hex nut until becoming tight. Attach the crossbar to the junction box using two box screws. The side of the crossbar marked "GND" must face out.
4. Follow wiring instructions carefully (see 'Wiring' section below).
5. એલ ની પાછળની પ્લેટ જોડોamp body (A) onto the junction box, aligning the screws on the crossbar with the mounting holes and locking it securely with the ball nuts (C). Place the candle sleeve (B) over the lamp ધારક
6. Install the light bulbs in accordance with the fixture's specifications. મહત્તમ વોટને ઓળંગશો નહીંTAGઇ રેટિંગ!
7. With silicone caulking compound, caulk completely around the back of the cover to prevent water from seeping into the outlet box.

Image: Figure 1 - An exploded diagram illustrating the components and assembly sequence for mounting the outdoor wall lantern, including the junction box, supply wire, hex nut, mounting screw, supply ground wire, crossbar, box screw, fixture ground wire, fixture wire, and the main fixture body (A) with candle sleeve (B).

વાયરિંગ

1. Connect the electrical wires as follows: Connect the black wire from the fixture to the black (hot) wire from the house. Connect the white wire from the fixture to the white (neutral) wire from the house. Make sure all wire nuts are secured.
2. You may wrap the connections with electrical tape. If your outlet box has a ground wire (green or bare copper), connect the fixture's ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the crossbar.
3. દિવાલના જંકશન બોક્સમાં વાયર કનેક્શનને સરસ રીતે ટક કરો.

Image: Figure 2 - A diagram showing standard wiring connections for a light fixture, illustrating how fixture wires (black, white, and ground) connect to house wires (black, white, and ground/bare copper) using wire nuts.

ઓપરેટિંગ સૂચનાઓ

Once installed, restore power at the circuit breaker. The Livex Lighting 2161-02 Outdoor Wall Lantern operates with a standard wall switch (not included). If connected to a compatible dimmer switch, the light output can be adjusted. This fixture is designed for incandescent bulbs and is dimmable with appropriate dimming controls.

જાળવણી

સફાઈ

To maintain the finish and appearance of your fixture, clean it regularly with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or polishes as they may damage the finish. For glass panels, use a mild glass cleaner applied to a cloth, not directly to the fixture.

બલ્બ રિપ્લેસમેન્ટ

Always turn off the power at the circuit breaker before replacing bulbs. Allow bulbs to cool completely before touching them. Use only bulbs that meet the specified wattage and type (E26 base, up to 100 watts incandescent). Exceeding the maximum wattage can cause overheating and damage to the fixture.

મુશ્કેલીનિવારણ

• લાઇટ ચાલુ થતી નથી:
  • સર્કિટ બ્રેકર પર પાવર ચાલુ છે કે નહીં તે તપાસો.
  • ખાતરી કરો કે બલ્બ સોકેટમાં સુરક્ષિત રીતે સ્ક્રૂ થયેલો છે અને બળી ગયો નથી.
  • Verify all wire connections are secure and correctly made.
• પ્રકાશ ઝબકતો:
  • ખાતરી કરો કે બલ્બ સંપૂર્ણપણે કડક છે.
  • છૂટક વાયર જોડાણો માટે તપાસો.
  • If using a dimmer, ensure it is compatible with incandescent bulbs and the bulb itself is dimmable.
• Glass panels are loose:
  • Carefully inspect the fixture for any retaining clips or screws that may need tightening.

વિશિષ્ટતાઓ

વોરંટી માહિતી

This Livex Lighting fixture comes with a 1-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For specific warranty details and limitations, please contact Livex Lighting customer service.

આધાર

For further assistance, technical support, or to inquire about replacement parts, please visit the official Livex Lighting store or contact their customer service department.

Livex Lighting Store: Livex Lighting on Amazon