Genie 36163R.S IntelliCode ગેરેજ ડોર ઓપનર રીસીવર સૂચના માર્ગદર્શિકા

1. પરિચય

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Genie 36163R.S IntelliCode Garage Door Opener Receiver. This receiver is designed to enhance the compatibility of your garage door opener system with Genie IntelliCode remotes, operating on both 315MHz and 390MHz frequencies.

Please read all instructions carefully before beginning installation or operation to ensure proper function and safety.

2. પેકેજ સામગ્રી

The Genie 36163R.S IntelliCode Receiver package includes:

• One (1) Genie 36163R.S IntelliCode Receiver unit.

નોંધ: This package contains the receiver unit only. Transmitters (remotes), wiring, and power packs are not included and must be acquired separately if needed. This receiver is commonly used as a component in the GIRUD-1T Receiver Kit.

3. સલામતી માહિતી

હંમેશા નીચેની સલામતી સાવચેતીઓનું પાલન કરો:

• Disconnect power to the garage door opener before installing or servicing the receiver.
• ખાતરી કરો કે બધા વાયરિંગ કનેક્શન સુરક્ષિત છે અને સ્થાનિક ઇલેક્ટ્રિકલ કોડ્સનું પાલન કરે છે.
• Keep hands and clothing clear of the garage door and its moving parts during operation.
• Do not allow children to operate the garage door opener or play with remote controls.
• Test the safety reversal system of your garage door opener after installation.

4. સેટઅપ અને ઇન્સ્ટોલેશન

The Genie 36163R.S receiver is designed for straightforward installation. Follow these steps:

4.1. Identify Components

આકૃતિ 1: ટોચ view of the Genie 36163R.S IntelliCode Receiver. This image shows the overall compact design of the receiver unit.

આકૃતિ 2: નીચે view of the Genie 36163R.S IntelliCode Receiver. The label displays the receiver model (315390R2) and FCC compliance information.

આકૃતિ 3: બાજુ view of the Genie 36163R.S IntelliCode Receiver. This image highlights the POWER, COMMON, and WALLBUTTON TERMINAL connections, along with the LEARN CODE INDICATOR LED and LEARN CODE BUTTON.

4.2. Wiring the Receiver

1. પાવર ડિસ્કનેક્ટ કરો: Before making any connections, ensure the power to your garage door opener is disconnected at the circuit breaker.
2. Locate Terminals: On your garage door opener power head, locate the terminals for the wall control button. These are typically labeled "COMMON" and "WALL BUTTON" or similar.
3. Connect Receiver Wires:
   • Connect a wire from the receiver's "COMMON" terminal to the "COMMON" terminal on your garage door opener.
   • Connect a wire from the receiver's "WALLBUTTON TERMINAL" to the "WALL BUTTON" terminal on your garage door opener.
   • Connect the receiver's "POWER" terminal to a 24-volt power source. This may be available from your garage door opener's accessory terminals or require a separate 24V power pack (not included).
4. સુરક્ષિત જોડાણો: ખાતરી કરો કે તમામ વાયર કનેક્શન ચુસ્ત અને સુરક્ષિત છે.

4.3. રીસીવર માઉન્ટ કરવું

Mount the receiver in a location that is protected from moisture and physical damage, preferably near the garage door opener. Ensure the antenna wire hangs freely and is not coiled or obstructed for optimal signal reception.

5. Operating Instructions: Programming Remotes

This receiver is compatible with Genie IntelliCode remotes. To program a remote to the receiver:

1. પાવર પુન Restસ્થાપિત કરો: Reconnect power to your garage door opener. The LEARN CODE INDICATOR LED on the receiver should illuminate or flash.
2. Press Learn Button: Press and release the "LEARN CODE BUTTON" on the receiver (refer to Figure 3). The LEARN CODE INDICATOR LED will begin to flash slowly.
3. રિમોટ સક્રિય કરો: Within 30 seconds, press and release the button on your IntelliCode remote control that you wish to program.
4. પુષ્ટિ: The LEARN CODE INDICATOR LED on the receiver will stop flashing and remain lit for a moment, then turn off, indicating successful programming.
5. દૂરસ્થ પરીક્ષણ: Press the programmed button on your remote control to test the garage door opener's operation.
6. Program Additional Remotes: Repeat steps 2-5 for any additional IntelliCode remotes you wish to program.

નોંધ: If the remote does not operate the garage door, ensure the remote has fresh batteries and repeat the programming steps.

6. મુશ્કેલીનિવારણ

• Receiver not responding:
  • Check power connections to the receiver. Ensure 24V power is supplied.
  • Verify wiring to the garage door opener's wall button terminals is correct and secure.
  • Ensure the garage door opener itself has power.
• Remote not operating door after programming:
  • Confirm the remote is a Genie IntelliCode remote.
  • Check the remote's battery. Replace if necessary.
  • પ્રોગ્રામિંગ પગલાં કાળજીપૂર્વક પુનરાવર્તિત કરો.
  • ખાતરી કરો કે રિમોટ રીસીવરની રેન્જમાં છે.
• Reduced remote range:
  • Ensure the receiver's antenna wire is fully extended and not obstructed or coiled.
  • Check for sources of radio interference (e.g., other electronic devices, metal objects).
  • Consider relocating the receiver for better line-of-sight to where remotes are typically used.

7. સ્પષ્ટીકરણો

8. જાળવણી

The Genie 36163R.S IntelliCode Receiver requires minimal maintenance. Periodically:

• Inspect wiring for any signs of wear or damage.
• Ensure the receiver is free from dust and debris.
• Verify the antenna is unobstructed.

No user-serviceable parts are inside the receiver unit. Do not attempt to open or repair the unit yourself.

9. વોરંટી અને સપોર્ટ

For warranty information or technical support, please refer to the official Genie website or contact Genie customer service. Keep your purchase receipt for warranty claims.

Genie Customer Service: Refer to product packaging or the official Genie webવર્તમાન સંપર્ક માહિતી માટે સાઇટ.