1. પરિચય
This manual provides detailed instructions for the installation, programming, operation, and maintenance of the UHPPOTE HBK-A02 125KHz RFID Standalone Door Access Control Keypad. This device is designed to provide secure access control for various applications, supporting up to 1000 card users.
Figure 1: UHPPOTE HBK-A02 Keypad Front View
2. મુખ્ય લક્ષણો
- High quality and high security, sensitively and response quickly.
- Full programming from the keypad, support add/delete cards, set password, etc.
- Door bell button support external doorbell.
- Uses high-performance MCU for stable performance and low-power circuit for extended service life.
- Functions as a standalone keypad, no computer connection required.
- Suitable for factories, houses, residential quarters, offices, and mechanical/electrical control equipment.
3. સ્પષ્ટીકરણો
| લક્ષણ | વિગત |
|---|---|
| મોડલ નંબર | HBK-A02 |
| ઉત્પાદક | UHPPOTE |
| ઇનપુટ વોલ્યુમtage | 12 વોલ્ટ ડીસી |
| ઉત્પાદન પરિમાણો | 4.72 x 3.07 x 0.87 ઇંચ |
| વસ્તુનું વજન | ૬.૭ ઔંસ (૧૮૮.૮ ગ્રામ) |
| RFID આવર્તન | 125KHz |
| વપરાશકર્તા ક્ષમતા | Up to 1000 Card Users |
| રંગ | કાળો |
| યુપીસી | 701385688196 |
4. સ્થાપન
Proper installation is crucial for the optimal performance and security of your access control keypad. Ensure all power is disconnected before beginning installation.
૪.૨ કીપેડ માઉન્ટ કરવું
- Choose a suitable mounting location near the door, ensuring it is protected from direct weather exposure if installed outdoors.
- Use the provided mounting screws to secure the back plate of the keypad to the wall.
- Route the necessary wiring through the wall or conduit to the keypad's connection point.
- Attach the keypad front panel to the back plate after wiring is complete.
Figure 2: Keypad Mounted on a Door Frame
4.2 વાયરિંગ કનેક્શન્સ
The HBK-A02 keypad requires a 12V DC power supply. Carefully follow the wiring diagrams below. Incorrect wiring can damage the device or connected components.
આકૃતિ 3: પાછળ View of Keypad with Wiring Harness
Figure 4: Close-up of Wiring Terminal Block
4.2.1 Common Power Supply Diagram
This diagram illustrates connections when using a single power supply for both the keypad and the electric lock.
Figure 5: Common Power Supply Wiring Diagram
4.2.2 Special Power Supply Diagram
This diagram shows connections when using a dedicated access control power supply unit, which often includes battery backup and advanced control features.
Figure 6: Special Power Supply Wiring Diagram
5. પ્રોગ્રામિંગ
The keypad is programmed directly using the numeric buttons. The default master code is 123456.
5.1 પ્રોગ્રામિંગ મોડમાં પ્રવેશવું
- દબાવો *.
- Enter the 6-digit Master Code (default: 123456).
- દબાવો #.
- The red LED will flash, indicating programming mode.
5.2 Exiting Programming Mode
દબાવો * to exit programming mode at any time.
5.3 માસ્ટર કોડ બદલવો
- પ્રોગ્રામિંગ મોડ દાખલ કરો.
- દબાવો 0.
- Enter the new 6-digit Master Code.
- Enter the new 6-digit Master Code again to confirm.
- દબાવો #.
- પ્રોગ્રામિંગ મોડમાંથી બહાર નીકળો.
5.4 Adding User Cards/Codes
The keypad supports up to 1000 user cards or codes.
- પ્રોગ્રામિંગ મોડ દાખલ કરો.
- દબાવો 1.
- For RFID cards: Present the card to the keypad. The keypad will beep to confirm. Repeat for additional cards.
- For User Codes: Enter a 4-digit to 6-digit user code, then press #. Enter the code again and press # ખાતરી કરવા માટે.
- પ્રોગ્રામિંગ મોડમાંથી બહાર નીકળો.
5.5 Deleting User Cards/Codes
- પ્રોગ્રામિંગ મોડ દાખલ કરો.
- દબાવો 2.
- For RFID cards: Present the card to the keypad. The keypad will beep to confirm deletion. Repeat for additional cards.
- For User Codes: Enter the 4-digit to 6-digit user code to delete, then press #.
- પ્રોગ્રામિંગ મોડમાંથી બહાર નીકળો.
5.6 Setting Relay Unlock Time
This sets how long the door remains unlocked after a valid access. The default is 5 seconds.
- પ્રોગ્રામિંગ મોડ દાખલ કરો.
- દબાવો 3.
- Enter a 2-digit number for the unlock time in seconds (e.g., 05 5 સેકન્ડ માટે, 00 0.2 સેકન્ડ માટે).
- દબાવો #.
- પ્રોગ્રામિંગ મોડમાંથી બહાર નીકળો.
6. ઓપરેશન
6.1 Gaining Access
- Using an RFID Card: Present a registered RFID card to the keypad. The keypad will beep, and the door will unlock for the set duration.
- યુઝર કોડનો ઉપયોગ: Enter your registered user code (4-6 digits) followed by #. The keypad will beep, and the door will unlock for the set duration.
૬.૪ ડોરબેલ ફંક્શન
દબાવો બેલ button on the keypad to activate an external doorbell (if connected).
7. જાળવણી
- સફાઈ: Wipe the keypad surface with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- પર્યાવરણીય સંરક્ષણ: Ensure the keypad is protected from extreme temperatures, direct sunlight, and moisture to prolong its lifespan.
- નિયમિત પરીક્ષણ: Periodically test the keypad's functionality, including card/code access and the exit button, to ensure proper operation.
8. મુશ્કેલીનિવારણ
| સમસ્યા | સંભવિત કારણ | ઉકેલ |
|---|---|---|
| Keypad does not power on. | પાવર સપ્લાય નથી કે ખોટી વાયરિંગ નથી. | Check 12V DC power supply connection and wiring according to diagrams. |
| Door does not unlock with valid card/code. | Card/code not registered, incorrect code, or lock wiring issue. | Verify card/code registration. Check wiring to the electric lock (NO/NC/COM). Ensure relay unlock time is set correctly. |
| Keypad beeps continuously or acts erratically. | Interference or internal fault. | Disconnect power for 30 seconds and reconnect. If problem persists, contact support. |
| Cannot enter programming mode. | Incorrect Master Code or not following sequence. | Ensure you are using the correct 6-digit Master Code (default 123456) and the sequence * + માસ્ટર કોડ + #. |
9. સલામતી માહિતી
- કોઈપણ વાયરિંગ અથવા જાળવણી કરતા પહેલા હંમેશા પાવર ડિસ્કનેક્ટ કરો.
- Ensure all wiring connections are secure and insulated to prevent short circuits.
- ઉપકરણને પાણી અથવા વધુ પડતા ભેજના સંપર્કમાં ન લાવો.
- This device is intended for low-voltage applications (12V DC). Do not connect to higher voltage સ્ત્રોતો.
- Installation should be performed by qualified personnel if you are unsure about electrical wiring.
