WaterCop Wireless Flood Sensor (WCDFS1) Instruction Manual

1. પરિચય

The WaterCop Wireless Flood Sensor (WCDFS1) is designed to detect the presence of water and transmit a wireless signal to a compatible WaterCop automatic water shut-off system. This system helps prevent water damage by automatically activating the shut-off valve when a leak is detected.

This sensor operates wirelessly, providing flexible placement options up to 200 feet from the main WaterCop system. It is powered by standard AA alkaline batteries.

2. પેકેજ સામગ્રી

• WaterCop Wireless Flood Sensor (WCDFS1)
• Remote Probe with cable
• માઉન્ટ કરવાનું હાર્ડવેર (સ્ક્રૂ, એન્કર)
• આ સૂચના માર્ગદર્શિકા

3. સલામતી માહિતી

• ઇન્સ્ટોલેશન અને ઓપરેશન પહેલાં બધી સૂચનાઓ વાંચો.
• Do not expose the sensor to extreme temperatures or direct sunlight.
• Ensure batteries are installed correctly according to polarity markings.
• Replace batteries annually or when indicated by the WaterCop system.
• આ ઉપકરણ માત્ર ઇન્ડોર ઉપયોગ માટે બનાવાયેલ છે.

4. સેટઅપ અને ઇન્સ્ટોલેશન

4.1 બેટરી ઇન્સ્ટોલેશન

The WaterCop WCDFS1 sensor requires two (2) AA alkaline batteries (not included).

1. સેન્સર c કાળજીપૂર્વક ખોલોasing. Refer to the diagram for assistance.
2. Insert two AA alkaline batteries, observing the correct polarity (+/-) as marked inside the battery compartment.
3. સેન્સર બંધ કરો casing સુરક્ષિત રીતે.

A pair of standard AA alkaline batteries should operate the sensor for approximately one year.

4.2 સેન્સર પ્લેસમેન્ટ

Place the sensor in areas prone to water leaks, such as near water heaters, washing machines, dishwashers, sinks, toilets, or in basements.

The sensor transmits a wireless signal up to 200 feet to the WaterCop control unit. Consider potential obstructions like thick walls or metal objects that may reduce signal range.

The remote probe should be positioned directly on the floor or surface where water accumulation is most likely to occur.

4.3 Pairing with WaterCop System

The WCDFS1 sensor is compatible with all WaterCop systems. Refer to your specific WaterCop control unit's manual for detailed instructions on how to pair new sensors. Generally, this involves placing the control unit into a "learn" mode and then activating the sensor.

4.4 માઉન્ટ કરવાનું

The sensor unit can be wall-mounted using the provided hardware. Ensure the remote probe cable reaches the desired detection area.

5. ઓપરેશન

Once installed and paired, the WaterCop Wireless Flood Sensor continuously monitors for the presence of water at its remote probe.

Upon detecting water, the sensor immediately transmits a wireless signal to the WaterCop control unit.

The WaterCop control unit, upon receiving this signal, will activate the automatic shut-off valve, thereby stopping the water supply to prevent further damage.

The sensor will continue to transmit the alarm signal until the water is no longer detected by the probe.

6. જાળવણી

6.1 બેટરી રિપ્લેસમેન્ટ

Replace the AA alkaline batteries annually or when the WaterCop control unit indicates a low battery signal from the sensor.

1. Open the sensor casing.
2. જૂની બેટરીઓ દૂર કરો અને જવાબદારીપૂર્વક તેનો નિકાલ કરો.
3. યોગ્ય ધ્રુવીયતા સુનિશ્ચિત કરીને, બે નવી AA આલ્કલાઇન બેટરી દાખલ કરો.
4. સેન્સર બંધ કરો casing સુરક્ષિત રીતે.

6.2 સફાઈ

Periodically inspect the sensor and probe for dust or debris. Clean with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.

6.3 પરીક્ષણ

It is recommended to test the sensor's functionality periodically (e.g., every 3-6 months).

1. Place a small amount of water (e.g., a few drops) on the remote probe.
2. Observe if the WaterCop control unit receives the alarm signal and activates the shut-off valve.
3. Remove the water from the probe and verify that the WaterCop system resets or allows manual reset.
4. Refer to your WaterCop control unit's manual for specific testing procedures.

7. મુશ્કેલીનિવારણ

7.1 Sensor not detecting water:

• Ensure the remote probe is making good contact with the surface.
• બેટરી સ્તર તપાસો અને જો જરૂરી હોય તો બદલો.
• Verify the sensor is correctly paired with the WaterCop control unit.

7.2 WaterCop system not responding to sensor:

• Check the sensor's batteries.
• Ensure the sensor is within the 200 ft wireless range of the WaterCop control unit and there are no significant obstructions.
• Re-pair the sensor with the WaterCop control unit.
• Consult the WaterCop control unit's manual for troubleshooting its reception.

7.3 False alarms:

• Ensure the probe is not placed in an area where condensation or minor spills are common and not indicative of a leak.
• Check for any moisture on the probe that might be causing a false trigger.

8. સ્પષ્ટીકરણો

9. વોરંટી અને સપોર્ટ

For warranty information and technical support, please refer to the official WaterCop webસાઇટ પર જાઓ અથવા તેમની ગ્રાહક સેવાનો સીધો સંપર્ક કરો. વોરંટી દાવાઓ માટે તમારી ખરીદી રસીદ રાખો.

Official WaterCop Webસાઇટ: www.watercop.com

Contact Information: Refer to the webવર્તમાન સંપર્ક વિગતો માટે સાઇટ.