સ્ટેટ્સમ વલ્કન 9K EQ - 1 ઓહ્મ 9000W RMS ફુલ રેન્જ હાઇ પાવર Ampજીવંત વપરાશકર્તા માર્ગદર્શિકા

પરિચય

Thank you for choosing the Stetsom Vulcan 9K EQ - 1 Ohm 9000W RMS Full Range High Power Amplifier. This manual provides essential information for the proper installation, operation, and maintenance of your amplifier. Please read this manual thoroughly before using the product to ensure optimal performance and safety.

મહત્વપૂર્ણ સલામતી માહિતી

• Always disconnect the vehicle's battery before making any electrical connections.
• ઇલેક્ટ્રિકલ જોખમોને રોકવા માટે યોગ્ય ગ્રાઉન્ડિંગની ખાતરી કરો.
• ઇન્સ્ટોલ કરો ampવધુ ગરમ થવાથી બચવા માટે સારી રીતે વેન્ટિલેટેડ વિસ્તારમાં લિફાયર.
• Use appropriate gauge wiring for power and speaker connections as specified in this manual.
• ખુલ્લા પાડવાનું ટાળો ampભેજ અથવા આત્યંતિક તાપમાન માટે લિફાયર.
• ખોલવાનો કે રિપેર કરવાનો પ્રયાસ કરશો નહીં amplifier yourself. Refer all servicing to qualified personnel.

ઉત્પાદન ઓવરview

The Stetsom Vulcan 9K EQ is a high-power, full-range digital amplifier designed for automotive audio systems. It features a robust design and advanced equalization capabilities to deliver powerful and clear sound reproduction.

મુખ્ય લક્ષણો:

• 9000W RMS power output at 1 Ohm (12.6V)
• Full Range frequency response (10Hz to 15KHz)
• Built-in 3-band equalizer (Bass, Mid Bass, Mid High)
• Over Clip +15% Power indicator
• Protection circuits for safe operation

ઘટક ઓળખ:

આ amplifier features power, protection, and clip indicators on the front panel. The input and output terminals are located on the side for easy access during installation.

ઇન્સ્ટોલેશન અને સેટઅપ

1. પાવર કનેક્શન્સ:

• Power Cable (B+): Connect a heavy-gauge power cable directly from the positive terminal of the vehicle's battery to the B+ terminal on the amplifier. An inline fuse or circuit breaker (not included) must be installed within 18 inches (45 cm) of the battery.
• Ground Cable (GND): Connect a heavy-gauge ground cable from the GND terminal on the amplifier to a clean, unpainted metal surface of the vehicle chassis. Ensure a solid, low-resistance connection.
• રિમોટ ટર્ન-ઓન (REM): Connect a remote turn-on wire from your head unit's remote output to the REM terminal on the amplifier. This wire signals the amplifier to turn on and off with your audio system.

2. Audio Input Connections:

Connect RCA cables from your head unit's pre-out (RCA output) to the RCA input jacks on the amplifier. Ensure correct left and right channel connections if applicable, though this is a mono ampજીવંત

3. Speaker Output Connections:

Connect your subwoofer(s) or full-range speakers to the speaker output terminals on the amplifier. Pay close attention to polarity (+ and -) and ensure the total impedance of your speakers matches the amplifier's rated impedance (1 Ohm for this model). Refer to the specifications section for impedance details.

4. માઉન્ટ કરવાનું:

માઉન્ટ કરો amplifier securely in a location that provides adequate ventilation and protection from moisture. Avoid mounting it directly on carpet or in enclosed spaces without airflow.

ઓપરેટિંગ સૂચનાઓ

1. Initial Power-Up:

After all connections are made, reconnect the vehicle's battery. Turn on your head unit. The "POWER" indicator on the ampલાઇફાયર પ્રકાશિત થવું જોઈએ, જે દર્શાવે છે કે તે પાવર પ્રાપ્ત કરી રહ્યું છે અને કાર્યરત છે.

2. Gain Adjustment:

પર ગેઇન કંટ્રોલ એડજસ્ટ કરો ampઆઉટપુટ વોલ્યુમ સાથે મેળ ખાતું લાઇફાયરtage of your head unit. Start with the gain at its minimum setting. Play a familiar track at about 75% of your head unit's maximum volume. Slowly increase the amplifier's gain until you hear distortion, then back it off slightly. The "CLIP" indicator should only flash briefly on very dynamic peaks, not stay illuminated.

3. Crossover Settings:

The Vulcan 9K EQ features adjustable crossovers:

• લો પાસ ફિલ્ટર (LPF): Adjust this control to set the upper frequency limit for your subwoofers. Frequencies above this setting will be attenuated.
• હાઇ પાસ ફિલ્ટર (HPF): Adjust this control to set the lower frequency limit for your speakers. Frequencies below this setting will be attenuated. This is typically used for full-range speakers or mid-bass drivers.

Refer to your speaker manufacturer's recommendations for optimal crossover points.

4. Equalizer Adjustment (3-Band EQ):

આ amplifier includes a 3-band equalizer to fine-tune the audio output:

• બાસ: ઓછી-આવર્તન પ્રતિભાવને સમાયોજિત કરે છે.
• મિડ બાસ: Adjusts the mid-low frequency response.
• મધ્યમ ઉચ્ચ: Adjusts the mid-high frequency response.

Make small adjustments and listen carefully to achieve your desired sound balance. Avoid excessive boosting, which can lead to distortion or speaker damage.

જાળવણી

• રાખો amplifier clean and free from dust and debris. Use a soft, dry cloth for cleaning.
• આસપાસ પૂરતો હવા પ્રવાહ સુનિશ્ચિત કરો amplifier at all times to prevent overheating. Regularly check that cooling fins are not obstructed.
• Periodically check all wiring connections for tightness and corrosion. Loose connections can cause performance issues or damage.

મુશ્કેલીનિવારણ માર્ગદર્શિકા

ટેકનિકલ વિશિષ્ટતાઓ

વોરંટી અને આધાર

Stetsom products are manufactured to the highest quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Stetsom website. For technical support or service inquiries, please contact your authorized Stetsom dealer or Stetsom customer service.

Webસાઇટ: www.stetsom.com.br (માજીampલી લિંક, વાસ્તવિક લિંક અલગ અલગ હોઈ શકે છે)