ઉત્પાદન ઓવરview
The PHOENIX CONTACT UTME 6 is a high-quality test disconnect terminal block designed for reliable electrical connections in industrial applications. Featuring 2 connections, it is rated for 30 Amps and 500 Volts, accommodating wires up to 6 MM². Its screw connection method ensures secure and durable wiring. This terminal block is ideal for circuits requiring easy testing and disconnection without interrupting the main circuit flow.
Figure 1: PHOENIX CONTACT UTME 6 Test Disconnect Terminal Block, showing its compact design and screw terminals.
સલામતી માહિતી
- Always disconnect power before installing, servicing, or removing the terminal block.
- Installation should only be performed by qualified personnel in accordance with local and national electrical codes.
- Ensure proper wire gauge and insulation are used for the specified current and voltagઇ રેટિંગ્સ.
- Do not exceed the maximum current (30A) or voltage (500V) ratings.
- Verify all connections are secure to prevent loose contacts and potential hazards.
- Protect the terminal block from moisture, dust, and extreme temperatures.
સેટઅપ અને ઇન્સ્ટોલેશન
Follow these steps for proper installation of the UTME 6 terminal block:
- અનપેકીંગ: Carefully remove the terminal block from its packaging. Inspect for any visible damage.
- માઉન્ટ કરવાનું: The UTME 6 is designed for DIN rail mounting. Snap the terminal block onto a standard DIN rail (e.g., NS 35/7.5 or NS 35/15) by pressing it down firmly until it clicks into place.
- વાયરની તૈયારી: Strip approximately 9-10 mm of insulation from the end of the wire. For stranded wires, it is recommended to use ferrules for optimal connection integrity.
- વાયરિંગ કનેક્શન્સ:
- Using a suitable screwdriver, open the screw clamp ટર્મિનલ બ્લોક પર.
- Insert the prepared wire fully into the clampએકમ
- Tighten the screw firmly to secure the wire. Ensure no bare wire strands are exposed outside the clampએકમ
- Repeat for all necessary connections.
- પરીક્ષણ: After all connections are made, perform continuity and insulation resistance tests as required by local regulations before applying power.
ઓપરેટિંગ સૂચનાઓ
The UTME 6 features a test disconnect function, allowing for easy isolation of circuits for testing or maintenance without disturbing the main wiring.
- સામાન્ય કામગીરી: In its standard configuration, the terminal block provides a continuous electrical path.
- Disconnecting for Test: To disconnect the circuit, simply open the disconnect knife or lever (if applicable to the specific variant, for UTME 6, it's typically a screw-operated disconnect). This isolates the circuit section connected to the terminal block.
- પુનઃજોડાણ: To restore the connection, close the disconnect knife or lever. Ensure it is fully engaged for proper electrical contact.
Note: Always ensure power is off before performing any disconnect or reconnect operations if there is a risk of arc flash or other electrical hazards.
જાળવણી
Regular maintenance ensures the longevity and reliable performance of your UTME 6 terminal block.
- સફાઈ: Periodically clean the terminal block using a dry, lint-free cloth. Avoid using solvents or abrasive cleaners that could damage the plastic housing.
- નિરીક્ષણ: Visually inspect the terminal block for any signs of damage, discoloration, or loose connections. Check for corrosion on metal parts.
- સ્ક્રૂને ફરીથી કડક બનાવવું: Over time, screw connections can loosen due to vibration or thermal cycling. Periodically retighten the screw connections to the recommended torque (refer to PHOENIX CONTACT technical documentation for specific torque values, generally 0.5-0.8 Nm for M3 screws).
મુશ્કેલીનિવારણ
If you encounter issues with your UTME 6 terminal block, consider the following common problems and solutions:
| સમસ્યા | સંભવિત કારણ | ઉકેલ |
|---|---|---|
| No continuity through the block |
|
|
| Overheating/Discoloration |
|
|
| Difficulty inserting wire |
|
|
વિશિષ્ટતાઓ
| મોડલ નંબર | UTME 6 |
| બ્રાન્ડ | ફોનિક્સ સંપર્ક |
| વર્તમાન રેટિંગ | 30 Amps |
| ભાગtage રેટિંગ | 500 વોલ્ટ |
| વાયર ક્રોસ વિભાગ | 6 MM² (approx. 8 AWG) |
| જોડાણોની સંખ્યા | 2 |
| કનેક્ટર પ્રકાર | સ્ક્રૂ |
| ધ્રુવોની સંખ્યા | 2 |
| અનુપાલન | RoHS |
| પેકેજ પરિમાણો | 2 x 2 x 2 ઇંચ |
| વસ્તુનું વજન | 1.47 પાઉન્ડ |
વોરંટી માહિતી
PHOENIX CONTACT products are manufactured to the highest quality standards. This product is covered by the standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the official PHOENIX CONTACT webસાઇટ પર જાઓ અથવા તેમના ગ્રાહક સપોર્ટનો સીધો સંપર્ક કરો. ખરીદીના પુરાવા તરીકે તમારી ખરીદી રસીદ રાખો.
ગ્રાહક આધાર
For technical assistance, product inquiries, or support, please contact PHOENIX CONTACT customer service:
- Webસાઇટ: Visit the official PHOENIX CONTACT website for comprehensive product documentation, FAQs, and contact information. www.phoenixcontact.com
- ટેકનિકલ સપોર્ટ: નો સંદર્ભ લો website for regional technical support contact details (phone numbers, email addresses).
