SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. પરિચય

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

આકૃતિ 1.1: ફ્રન્ટ view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. સલામતી માહિતી

• ઇન્સ્ટોલેશન અને ઑપરેશન પહેલાં બધી સૂચનાઓ કાળજીપૂર્વક વાંચો.
• પાવર સપ્લાય વોલ્યુમની ખાતરી કરોtage matches the device's requirements (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Do not operate the device in environments with excessive moisture, dust, or corrosive gases.
• Disconnect power before performing any maintenance or wiring changes.
• ઉપકરણને મજબૂત ઇલેક્ટ્રોમેગ્નેટિક હસ્તક્ષેપથી દૂર રાખો.

3. ઉત્પાદન સુવિધાઓ

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Wide operating temperature range.
• Compact and easy-to-install design.

4. પેકેજ સામગ્રી

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• ૧ x વપરાશકર્તા માર્ગદર્શિકા (આ દસ્તાવેજ)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. સેટઅપ

5.1 માઉન્ટ કરવાનું

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2.૨.૨ વાયરિંગ

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Terminals 1 & 2: AC Power Supply (85-265V AC, 50/60Hz)
• Terminals 3 & 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Terminals 6 & 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Terminals 11 & 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. ઓપરેટિંગ સૂચનાઓ

6.1 ઓવર ડિસ્પ્લેview

The meter features a dual display:

• પીવી (પ્રક્રિયા મૂલ્ય): The upper red display shows the current measured temperature/humidity.
• SV (સેટ મૂલ્ય): The lower green display shows the desired set point.
• આઉટ સૂચક: Illuminates when the main output is active.
• એટી સૂચક: Illuminates when the auto-tuning function is active.
• AL1/AL2 Indicators: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 બટન કાર્યો

• સેટ બટન: પેરામીટર સેટિંગ મોડમાં પ્રવેશવા અને પસંદગીઓની પુષ્ટિ કરવા માટે વપરાય છે.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. સામાન્ય ઓપરેટિંગ મોડમાં, દબાવો સેટ button once. The SV display will begin to flash.
2. નો ઉપયોગ કરો ▲ (ઉપર) અને ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. દબાવો સેટ button again to confirm the new SV and exit the setting mode.

6.4 Advanced Parameter Settings

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the સેટ button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (ઉપર) અને ▼ (Down) buttons to navigate through parameters and the સેટ button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. જાળવણી

• સફાઈ: ડિસ્પ્લે સાફ કરો અને casinનરમ, સૂકા કપડાથી ઘર્ષક ક્લીનર્સ અથવા સોલવન્ટનો ઉપયોગ કરશો નહીં.
• નિરીક્ષણ: સમયાંતરે વાયરિંગ કનેક્શન ઢીલાપણું કે કાટ માટે તપાસો.
• સંગ્રહ: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. મુશ્કેલીનિવારણ

9. સ્પષ્ટીકરણો

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. વોરંટી અને સપોર્ટ

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webસંપર્ક માહિતી માટે સાઇટ.