Ecolink WST-232 Wireless Home Security Door Window Sensor User Manual

પરિચય

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ecolink WST-232 Wireless Home Security Door Window Sensor. This device is designed to enhance the security of your home by detecting the opening and closing of doors and windows. It is compatible with Honeywell 5800 Wireless and 2GIG security systems.

મહત્વપૂર્ણ સલામતી માહિતી

• ઇન્સ્ટોલેશન અને ઉપયોગ કરતા પહેલા બધી સૂચનાઓ કાળજીપૂર્વક વાંચો.
• Do not attempt to repair or modify the sensor. Refer all servicing to qualified personnel.
• Keep batteries out of reach of children. Dispose of used batteries properly according to local regulations.
• Ensure the sensor is installed in a location where it will not be exposed to extreme temperatures or moisture.

પેકેજ સામગ્રી

ખાતરી કરો કે બધી વસ્તુઓ પેકેજમાં હાજર છે:

• Ecolink WST-232 Wireless Door/Window Sensor (Main Unit)
• Magnet (for contact detection)
• Mounting Hardware (screws, adhesive tape)
• Interchangeable Brown Case
• વપરાશકર્તા માર્ગદર્શિકા (આ દસ્તાવેજ)

ઉત્પાદન ઓવરview

The Ecolink WST-232 is a compact wireless sensor designed for monitoring the open/closed status of doors and windows. It features an internal reed switch for standard magnetic contact detection and an external contact input for connecting wired devices.

છબી: Ecolink WST-232 Wireless Door/Window Sensor showing the main unit and the external contact wires.

મુખ્ય ઘટકો:

• Main Sensor Unit: Contains the battery, wireless transmitter, and internal reed switch.
• ચુંબક: Triggers the internal reed switch when separated from the main unit.
• External Contact Input: Two wires (typically red and black) for connecting an external wired contact.
• બેટરી કમ્પાર્ટમેન્ટ: Located on the back of the main unit.

સેટઅપ અને ઇન્સ્ટોલેશન

1. બેટરી ઇન્સ્ટોલેશન

1. Open the sensor casing by gently prying it open from the side notch.
2. Insert the CR2032 lithium battery, ensuring the positive (+) side faces up.
3. સેન્સર બંધ કરો casing સુરક્ષિત રીતે.

2. Enrolling the Sensor with Your Security Panel

The WST-232 sensor is compatible with Honeywell 5800 Wireless and 2GIG security systems. Refer to your security panel's manual for specific enrollment procedures. General steps are as follows:

1. Put your security panel into programming mode for adding new wireless zones.
2. Activate the sensor by separating the magnet from the main unit, or by connecting/disconnecting the external contact wires. This sends a signal to the panel.
3. Confirm the sensor's serial number is learned by the panel.
4. Assign the sensor to an appropriate zone type (e.g., "Entry/Exit," "Perimeter").
5. Exit programming mode on your panel.

3. સેન્સર માઉન્ટ કરવું

Choose a suitable location on your door or window frame. The sensor and magnet should be mounted within 0.5 inches (1.27 cm) of each other when the door/window is closed.

છબી: Ecolink WST-232 sensor components including the main unit, magnet, and mounting screws.

સ્ક્રૂનો ઉપયોગ કરવો:

1. Position the main sensor unit on the stationary frame and the magnet on the moving part (door/window).
2. સ્ક્રુ છિદ્રોને ચિહ્નિત કરો.
3. જો જરૂરી હોય તો પાયલોટ છિદ્રો ડ્રિલ કરો.
4. Secure both the sensor and magnet with the provided screws.

Using Adhesive Tape (not recommended for long-term security):

1. Clean the mounting surfaces thoroughly.
2. Apply adhesive tape to the back of the sensor and magnet.
3. Press firmly onto the desired surfaces for at least 30 seconds.

4. External Contact Input

The WST-232 includes an external contact input for integrating other wired devices, such as recessed door contacts or pressure mats. Connect the two wires from your external device to the red and black wires of the WST-232 sensor. The sensor will transmit a signal when the external contact opens or closes.

સેન્સરનું સંચાલન

Once installed and enrolled, the Ecolink WST-232 sensor operates automatically. When the door or window it is monitoring opens, separating the magnet from the main unit (or opening the external contact), the sensor will transmit a signal to your security panel. This signal indicates an "open" state. When the door or window closes, bringing the magnet back into proximity (or closing the external contact), the sensor transmits a "closed" state signal.

Your security panel will then react according to its programming (e.g., trigger an alarm if the system is armed, log the event).

જાળવણી

બેટરી રિપ્લેસમેન્ટ

The sensor uses one CR2032 lithium battery. When the battery level is low, your security panel will typically display a low battery warning for the corresponding zone. To replace the battery:

1. Put your security panel into disarm or test mode to prevent false alarms.
2. સેન્સર c ને હળવેથી ખોલોasing.
3. જૂની CR2032 બેટરી દૂર કરો.
4. Insert a new CR2032 battery, ensuring correct polarity (+ side up).
5. સેન્સર બંધ કરો casing સુરક્ષિત રીતે.
6. Test the sensor to ensure it communicates with the panel.

સફાઈ

Clean the sensor and magnet with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.

મુશ્કેલીનિવારણ

વિશિષ્ટતાઓ

• મોડલ: ડબ્લ્યુએસટી -232
• સુસંગતતા: Honeywell 5800 Wireless, 2GIG
• પરિમાણો: 3 x 1.7 x 1 ઇંચ (અંદાજે)
• બેટરી: 1 x CR2032 Lithium Coin Cell
• ઓપરેટિંગ આવર્તન: 345 MHz
• ઉત્પાદક: Ecolink Intelligent Technology Inc
• યુપીસી: 657479755391

વોરંટી અને ટેકનિકલ સપોર્ટ

For warranty information and technical assistance, please refer to the official Ecolink webસાઇટ પર જાઓ અથવા તેમના ગ્રાહક સપોર્ટનો સીધો સંપર્ક કરો. ખરીદીના પુરાવા તરીકે તમારી ખરીદી રસીદ રાખો.

ઇકોલિંક Webસાઇટ: www.ecolink.com