JORGENSEN No.4 Wood Planer Blade User Guide

1. પરિચય

This manual provides essential information for the safe and effective use of your JORGENSEN No.4 Wood Planer Blade. Please read these instructions carefully before installation and operation to ensure optimal performance and longevity of the blade.

2. સલામતી માહિતી

WARNING: Planer blades are extremely sharp. Handle with extreme care to prevent injury.

• Always wear appropriate personal protective equipment, including safety glasses and gloves, when handling or working with the blade.
• Ensure the planer is disconnected from any power source (if applicable) or secured before attempting to install, remove, or adjust the blade.
• Keep fingers and other body parts clear of the blade's cutting edge at all times.
• Store the blade in a protective cover or case when not in use to prevent accidental contact and maintain sharpness.
• Do not use a dull or damaged blade, as this can lead to inefficient planing and potential kickback.

3. ઉત્પાદન ઓવરview

The JORGENSEN No.4 Wood Planer Blade is designed for use with No.4 smooth planes, offering high hardness and long edge retention for efficient woodworking. It is crafted from professional-level O1 tool steel.

મુખ્ય લક્ષણો

• Professional Level Blade: Made of 9CrWMn, a professional-level O1 tool steel.
• ઉન્નત કાર્યક્ષમતા: Improves cutting efficiency while minimizing blade wear.
• Optimal Sharpness: Finely sharpened for efficient wood planing.
• ટકાઉપણું: High hardness and long edge retention.
• ફરીથી વાપરી શકાય તેવું: Can be repeatedly utilized, sharpened, and adjusted for a long service life.

Blade Material and Quality

This image displays a close-up of the JORGENSEN O1 steel planer blade, highlighting its hardened surface and indicating its professional-grade quality with a hardness rating of HRC 62-64.

ઉત્પાદન પરિમાણો

The diagram illustrates the key dimensions of the planer blade: 50.8mm width, 176mm length, and 3mm thickness. The blade features a 25-degree bevel angle and weighs 158g. Its heavy gauge (1/8 inch or 3.0mm) is up to 1.6 times thicker than other products, contributing to a solid cut with minimal vibration.

4. સેટઅપ

Blade Assembly and Replacement

This image provides a step-by-step guide for replacing the planer blade. Step 1 shows loosening the clamping mechanism. Step 2 illustrates removing the old blade assembly. Step 3 details attaching the new blade to the chip breaker. Step 4 shows reinserting the assembled blade into the plane body.

એસેમ્બલી પ્રક્રિયાના દ્રશ્ય પ્રદર્શન માટે, કૃપા કરીને નીચેનો વિડિઓ જુઓ:

1. cl ઢીલું કરોamping screw on your plane to release the blade assembly.
2. Carefully remove the old blade and chip breaker assembly.
3. Separate the old blade from the chip breaker.
4. Attach the new JORGENSEN No.4 Wood Planer Blade to the chip breaker. Ensure the screw is tightened sufficiently to hold the blade securely, but allow for minor adjustments.
5. Reinsert the blade and chip breaker assembly into the plane body.
6. Proceed to the Operating section for fine-tuning the blade's position.

Ope. Opeપરેટિંગ

બ્લેડ ઊંડાઈ સમાયોજિત

The depth of cut is controlled by the depth adjustment wheel. The tightness of the clamping screw can affect the depth adjustment wheel's ability to control the speed of adjusting the blade's depth. Ensure the clamping screw is appropriately tightened to allow for smooth, controlled adjustments.

1. With the blade assembly in place, turn the depth adjustment wheel (typically located at the rear of the plane) to extend or retract the blade.
2. Turn clockwise to extend the blade for a deeper cut, and counter-clockwise to retract it for a shallower cut.
3. Make small adjustments and test on a scrap piece of wood until the desired cutting depth is achieved.

Adjusting Lateral Blade Position

The lateral adjustment lever controls the horizontal position of the blade. The tightness of the blade screw can affect the lateral adjustment lever's ability to control the horizontal adjustment speed of the blade. Ensure the blade screw is appropriately tightened for precise control.

1. Use the lateral adjustment lever (typically located near the blade) to shift the blade left or right.
2. Adjust until the blade is parallel to the sole of the plane and protrudes evenly across the mouth.
3. Once both depth and lateral adjustments are set, ensure all screws are securely tightened before use.

પ્લાનિંગ ટેકનિક

Proper planing technique involves consistent pressure, a smooth stroke, and understanding wood grain. For a visual guide on effective planing, watch the video below:

6. જાળવણી

• શાર્પનિંગ: Regularly sharpen your blade to maintain its cutting efficiency. A sharp blade reduces effort and produces cleaner cuts. Use appropriate sharpening stones or systems for O1 tool steel.
• સફાઈ: After each use, clean the blade and plane body to remove wood dust and resin. This prevents buildup that can hinder performance and cause corrosion.
• રસ્ટ નિવારણ: Apply a thin coat of camellia oil or a rust preventative to the blade and other metal parts after cleaning, especially if storing for extended periods.
• સંગ્રહ: Store the blade in a dry environment, ideally in its original packaging or a dedicated blade protector, to prevent damage and corrosion.

7. મુશ્કેલીનિવારણ

8. સ્પષ્ટીકરણો

• બ્રાન્ડ: Jorgensen
• મોડલ નંબર: 70731
• સામગ્રી: O1 Tool Steel (9CrWMn)
• રંગ: ચાંદી
• શૈલી: કોમ્પેક્ટ
• પાવર સ્ત્રોત: મેન્યુઅલ
• કટીંગ ડેપ્થ: 3 Millimeters (Blade Thickness)
• સમાવાયેલ ઘટકો: બ્લેડ
• વસ્તુનું વજન: 191 ગ્રામ
• પાર્સલ પરિમાણો: 21.79 x 7.01 x 1.9 સેમી
• યુપીસી: 044295707312

9. વોરંટી અને સપોર્ટ

For warranty information or technical support regarding your JORGENSEN No.4 Wood Planer Blade, please refer to the official JORGENSEN webસાઇટ પર જાઓ અથવા તેમની ગ્રાહક સેવાનો સીધો સંપર્ક કરો. ખરીદીના પુરાવા તરીકે તમારી ખરીદી રસીદ રાખો.