Happymodel Mobula7 75mm Freestyle BNF Drone User Manual

1. પરિચય

The Happymodel Mobula7 Freestyle BNF (Bind-N-Fly) is a 75mm ultra-light drone designed for freestyle flying. Weighing approximately 24.5 grams, this quadcopter features high-speed RS0802 KV25000 brushless motors and HQPROP 1.6-inch tri-blade propellers, providing an enhanced freestyle experience. It comes equipped with an HDZero AIO5 flight controller and a built-in SPI ExpressLRS 2.4GHz receiver, compatible with ExpressLRS v3.0 firmware.

2. શું શામેલ છે

કૃપા કરીને ચકાસો કે નીચે સૂચિબદ્ધ બધી વસ્તુઓ તમારા પેકેજમાં હાજર છે:

• 1x Happymodel Mobula7 Freestyle BNF Drone
• 1x Spare Canopy
• 1x Spare Propeller Set
• 1x સ્ક્રુડ્રાઈવર
• 1x Propeller Disassembly Tool

3. સ્પષ્ટીકરણો

Detailed technical specifications for the Mobula7 drone:

જનરલ

• વજન: 24.5g (બેટરી વિના)
• ભલામણ કરેલ બેટરી: 1S 450mAh / 550mAh / 650mAh (not included)
• પ્રોપેલરનું કદ: 40 મીમી
• યુપીસી: 086972527226
• ઉત્પાદક ભાગ નંબર: M53713 drone

AIO ફ્લાઇટ કંટ્રોલર

• એમસીયુ: STM32F411 (100MHz, 512K Flash)
• ગાયરો: ICM42688P
• ઓન-બોર્ડ વોલ્યુમtage અને ampએરેજ મીટર
• Built-in 5A (each) BLHeli_S 4-in-1 ESC (Bluejay ESC firmware pre-installed)
• Built-in 5.8GHz HDZero VTX
• Built-in SPI ExpressLRS 2.4GHz receiver (compatible with ExpressLRS v3.0)
• બિલ્ટ-ઇન 5 વી 1 એ બીઇસી
• બોર્ડનું કદ: 28.5x28.5mm with 25.5x25.5mm mounting holes
• Betaflight Firmware: CRAZYBEEF4SX1280 4.5.1 (factory default)

HDZero Lux Camera

• સેન્સરનું કદ: 1/2 ઇંચ
• ઠરાવ: 720p60 (4:3 and 16:9 aspect ratios)
• FOV (4:3): D:155° H:126° V:94°
• FOV (16:9): D:145° H:126° V:70°
• ડબ્લ્યુડીઆર (વાઇડ ડાયનેમિક રેંજ)

મોટર્સ

• મોડલ: RS0802
• Kv: 25000
• Stator Diameter: 8 મીમી
• સ્ટેટર લંબાઈ: 2 મીમી
• શાફ્ટ વ્યાસ: Φ1.5 મીમી
• વજન: 2.0 જી (દરેક)

4. સેટઅપ

Follow these steps to prepare your Mobula7 drone for its first flight.

4.1 બેટરી કનેક્શન

1. Ensure the drone's power switch (if present) is in the OFF position.
2. Connect a fully charged 1S LiPo battery (450mAh, 550mAh, or 650mAh recommended) to the drone's battery connector. Ensure correct polarity.
3. Secure the battery in the designated battery tray or strap.

4.2 ExpressLRS Receiver Binding

The Mobula7 features a built-in SPI ExpressLRS 2.4GHz receiver. To bind it with your ExpressLRS compatible radio transmitter:

1. Power on the Mobula7 drone by connecting the battery. The receiver's LED should start flashing slowly.
2. Power cycle the drone three times rapidly (connect battery, disconnect, connect, disconnect, connect). After the third connection, the receiver LED should flash rapidly, indicating it is in binding mode.
3. On your ExpressLRS compatible radio transmitter, navigate to the ExpressLRS LUA script or menu and select the 'BIND' option.
4. Once bound, the receiver LED on the drone will turn solid, indicating a successful connection.
5. If binding fails, ensure your transmitter's ExpressLRS firmware version is compatible with the drone's receiver (v3.0 or newer recommended).

4.3 Betaflight Configuration (Advanced Users)

The drone comes pre-configured with Betaflight firmware CRAZYBEEF4SX1280 4.5.1. For advanced settings or troubleshooting, you can connect to Betaflight Configurator:

1. Download and install the latest Betaflight Configurator software on your computer.
2. Connect the drone to your computer using a USB-C cable.
3. Open Betaflight Configurator and click 'Connect'.
4. You can now adjust PID settings, rates, OSD elements, and other advanced parameters. સાવધાન: Modifying settings without proper knowledge can lead to unstable flight or damage.

5. ઓપરેટિંગ સૂચનાઓ

This section provides guidance on safely operating your Mobula7 drone.

૭.૩ ફ્લાઇટ પહેલાની તપાસ

• Ensure propellers are securely attached and free from damage.
• Verify battery is fully charged and securely mounted.
• Check for any loose wires or components.
• Confirm your radio transmitter is powered on and bound to the drone.
• Perform a range check in a safe area before flying.

5.2 સશસ્ત્ર અને નિઃશસ્ત્રીકરણ

The drone's motors will not spin until it is armed. Arming and disarming procedures are typically configured in Betaflight:

• આર્મિંગ: Move the arming switch on your transmitter to the designated arm position. The motors will typically spin slowly, indicating readiness for flight.
• નિઃશસ્ત્રીકરણ: Move the arming switch back to the disarm position. The motors will stop spinning. In an emergency, you can also disarm by moving the throttle to zero and yawing hard left or right (check your Betaflight configuration for specific emergency disarm gestures).

૬.૫ મૂળભૂત ફ્લાઇટ નિયંત્રણો

Familiarize yourself with standard quadcopter controls:

• થ્રોટલ: Controls altitude (left stick up/down for Mode 2).
• વાહ: Rotates the drone horizontally (left stick left/right for Mode 2).
• પિચ: Tilts the drone forward/backward (right stick up/down for Mode 2).
• રોલ: Tilts the drone left/right (right stick left/right for Mode 2).

5.4 HDZero VTX Operation

The integrated HDZero VTX transmits video to your HDZero compatible goggles. Refer to your HDZero goggles manual for channel scanning and selection. The VTX settings (power, channel) can typically be adjusted via Betaflight OSD (On-Screen Display) menu using your transmitter sticks or through Betaflight Configurator.

6. જાળવણી

Regular maintenance ensures the longevity and optimal performance of your drone.

6.1 પ્રોપેલર રિપ્લેસમેન્ટ

Damaged propellers can significantly affect flight performance and safety. Replace them immediately if bent, cracked, or chipped.

1. Use the provided propeller disassembly tool to carefully remove the old propeller from the motor shaft.
2. Ensure the new propeller is oriented correctly (clockwise or counter-clockwise rotation as indicated by markings or motor direction).
3. Gently push the new propeller onto the motor shaft until it sits flush. Do not force it.

6.2 સફાઈ

After flights, especially in dusty or grassy environments, clean your drone:

• Use a soft brush or compressed air to remove dust and debris from motors, flight controller, and camera.
• Avoid using liquids directly on electronic components.

6.3 Motor Care

Inspect motors for any signs of damage or excessive wear. Ensure they spin freely without obstruction. If a motor feels gritty or makes unusual noises, it may require replacement.

6.4 ફર્મવેર અપડેટ્સ

Periodically check the Happymodel website or relevant community forums for updated Betaflight or ExpressLRS firmware. Updating firmware can introduce new features, improve performance, or fix bugs. Follow official update guides carefully.

7. મુશ્કેલીનિવારણ

This section addresses common issues you might encounter with your Mobula7 drone.

7.1 Drone Not Powering On

• બેટરી તપાસો: ખાતરી કરો કે બેટરી સંપૂર્ણપણે ચાર્જ થયેલ છે અને યોગ્ય રીતે જોડાયેલ છે.
• Inspect Connector: Verify the battery connector on the drone is not damaged or loose.
• દ્રશ્ય નિરીક્ષણ: Look for any visible damage to the flight controller or power distribution board.

7.2 No Video Signal (HDZero)

• ગોગલ સુસંગતતા: Ensure your goggles are HDZero compatible and powered on.
• Channel Match: Verify that your goggles are tuned to the same channel as the drone's VTX.
• એન્ટેના તપાસો: Ensure the VTX antenna on the drone and the antennas on your goggles are securely attached.
• VTX Power: Check VTX power settings in Betaflight OSD or Configurator.

7.3 Drone Not Arming

• Transmitter Link: Confirm your radio transmitter is powered on and successfully bound to the drone (solid receiver LED).
• Arming Switch: Ensure the arming switch on your transmitter is correctly configured and activated.
• Safety Pre-checks: Betaflight has safety checks. Connect to Betaflight Configurator and check the 'Setup' tab for any warnings (e.g., accelerometer calibration needed, low battery voltage, motor output issues).
• Throttle Position: Ensure your throttle stick is at its lowest position.

7.4 Unstable Flight / Drifting

• Propeller Damage: Inspect all propellers for damage and replace any that are bent, cracked, or chipped.
• મોટર સમસ્યાઓ: Check motors for debris, loose wires, or signs of damage. Ensure they spin smoothly.
• Accelerometer Calibration: In Betaflight Configurator, perform an accelerometer calibration on a level surface.
• PID Tuning: For advanced users, minor PID adjustments in Betaflight may be necessary, though the factory tune is generally suitable.

8. વોરંટી અને સપોર્ટ

Specific warranty information for the Happymodel Mobula7 drone is not provided in this manual. For details regarding warranty coverage, technical support, or service, please refer to the official Happymodel website or contact your retailer directly. Keep your proof of purchase for any warranty claims.