સેપ્ટર હોરાઇઝન વાયરલેસ કંટ્રોલર વપરાશકર્તા માર્ગદર્શિકા

નિયંત્રક સ્પષ્ટીકરણ

Charging Station Specifications

સિસ્ટમ જરૂરીયાતો

પેકેજ સામગ્રી

• Wireless controller × 1PC
• USB-A to USB-C cable 1PC
• Charging Station × 1PC
• Quick Start Guidex 1PC

Switch Console Wireless Connection

મહેરબાની કરીને નોંધ કરો: Ensure that the airplane mode on the console is turned off before use.
પગલું 1: Begin by setting the connection mode switch to the “NS” position located on the back of the controller.
પગલું 2: Power on the controller and navigate to the controller’s menu to select “Change Grip/Order.”
પગલું 3: Press and hold the sync button on the top of the controller for one second to enter Console Bluetooth Pairing mode;
LEDs 1 to 4 will flash rapidly in sequence.
પગલું 4: Once the connection is established successfully, LED 1 will remain illuminate.

જાગો અને ફરીથી કનેક્ટ કરો

Once the controller has successfully paired with the console:

• If the console is in SLEEP mode, pressing the HOME button on the controller can wake up both the controller and the console.
• If the console is already on, pressing any button on the controller will wake it up and allow it to reconnect to the console.

If you are unable to establish a connection, please follow these three steps:

• Disable Air plane mode on the console.
• Delete the controller’s information on the console (Navigate to System Settings > Controllers and Sensors >
• Disconnect Controllers)
• Repeat the First-Time Pairing steps.

કંટ્રોલર ઓટો સ્લીપ

• While on a wireless connection, press and hold the home button for 3 seconds to disconnect the controller and activate sleep mode.
• If no buttons are pressed within 5 minutes, the controller will automatically enter sleep mode.
• The controller will also enter sleep mode when the console is in sleep mode.

Switch Console Wired Connection

પગલું 1: Enable “Pro Controller Wired Communication on the console by navigating to System Settings > Controllers and Sensors Pro Controller Wired Communication > On.
મહેરબાની કરીને નોંધ કરો: Ensure that “Pro Controller Wired Communication” is enabled BEFORE connecting the controller and the Dock with the cable.
પગલું 2: Begin by adjusting the mode switch to the “NS” position located on the back of the controller
પગલું 3: Connect the controller to the console using a Type-C cable.

પગલું 4: Upon a successful connection, LED1 will begin to flash.

Audioડિઓ ફંક્શન

કંટ્રોલરમાં 3.5mm ઓડિયો પોર્ટ છે જે 3.5mm વાયર્ડ હેડસેટ્સ અથવા માઇક્રોફોનને સપોર્ટ કરે છે.
મહેરબાની કરીને નોંધ કરો:

• The audio function is functional ONLY in Wired Connection Mode with the console.
• It will NOT operate during wireless connections or when the controller is wired to a PC.
  

Ensure that ‘Pro Controller Wired Communication’ is turned on BEFORE connecting the controller and the Dock with the cable.

પગલું 1: Navigate to System Settings > Controllers and Sensors > Pro Controller Wired Communication and turn it On.
પગલું 2: Place the console in the dock and set it to TV mode.
પગલું 3: Connect the Dock and the controller using the USB cable.
પગલું 4: Look for the USB icon on the screen to confirm a successful wired connection,
પગલું 5: Insert the 3.5mm audio jack into the audio port located at the bottom of the controller.

Turbo and Auto-fire Setup

Buttons Available for Turbo Function: A/B/X/Y/LB/RB/LT/RT buttons

Setting Up the Turbo Function:

• Manual Turbo Function: Press and hold the Turbo button, then press any function button ONCE to activate the “Manual Turbo Function.”
• Auto Turbo Function: Repeat the first step above to switch to the “Auto Turbo Function.”
• Turning Off the Turbo Function: Repeat the first step after the “Auto Turbo Function” has been set,

Disabling All Turbo Functions for All Buttons:
Press and hold the Turbo button for 6 seconds until the controller vibrates, which will deactivate the turbo functions for al buttons.

ટર્બો સ્પીડ લેવલ:

• ધીમો: 5 shots/s, indicated by LED indicators flashing at a slow speed.
• મધ્યમ: 15 shots/s (Default Level), indicated by LED indicators flashing at a medium speed.
• ઝડપી: 25 shots/s, indicated by LED indicators flashing at a fast speed.

ટર્બો સ્પીડ લેવલ એડજસ્ટ કરો:

ટર્બો બટન દબાવો અને પકડી રાખો, ટર્બોની ગતિનો એક ગ્રેડ ઘટાડવા માટે જમણી જોયસ્ટિક નીચે દબાવો; ટર્બો સ્પીડનો એક ગ્રેડ વધારવા માટે જમણી જોયસ્ટિક ઉપર ખેંચો.

You can test and check the Turbo settings on a console by following these steps:
Go to Settings > Controllers and Sensors > Test Input Devices > Test Controller Buttons.

કંપનની તીવ્રતાને સમાયોજિત કરવી

There are four levels of Vibration Intensity: None, Weak, Medium, Strong.

• To Adjust the Vibration Intensity:
• ટર્બો બટન દબાવો અને પકડી રાખો.
• Move the left joystick UP to increase one grade of vibration intensity.
• Move the left joystick DOWN to decrease one grade of vibration intensity,

મેક્રો ડેફિનેશન ફંક્શન

• The controller features two macro-enabled programmable buttons “ML/MR” on the back, which can be programmed into function buttons or button sequences.
• Macro Buttons can be programmed to: A/B/X/Y/LB/RB/LT/RT/up/down/left/right buttons.

Setting up the Macro Definition:

પગલું 1: Press and hold the “Capture” “ML”/”MR” together for 2 seconds. A short vibration will remind you, and LED2-LED3 will stay lit, indicating the controller is ready to record the macro setting.
પગલું 2: Press the function buttons that need to be set sequentially. The controller will record the button with the time interval between each button pressed.
પગલું 3: Press the macro button ML or MR shortly to save. A short vibration will remind you, and the corresponding player LED light will stay lit, indicating that the macro definition setting has been saved. The last macro definition setting will automatically apply when the controller reconnects to the console.

મેક્રો ડેફિનેશન સેટિંગ્સ સાફ કરી રહ્યા છીએ:

પગલું 1: Press the “Capture” “ML”/”MR” together for 2 seconds to enter settings mode. A short vibration will remind you, and the LED2-LED3 will stay it.
પગલું 2: Exit setting mode by pressing the same ML/MR buttons, and the corresponding player LED will light up again, clearing the macro definition setting within the current slot.

RGB Lighting Control Instructions:

1. Startup Lighting Effect:
   • There are four controllable RGB lights under each of te left and right joysticks with a psychedelic gradient at startup.
   • Under ABXY, there is one controllable LED each that is on all the time (Light effect memory mode).
2. Lighting Display Modes:
   • The colored lights are categorized into three major groups of light display modes:
     a.Eight-color gradient mode.
     b.Changing color breathing mode.
     c.Fixed color mode.
3. Switching Light Effect Modes:
   • Press the START key and the LEFT key to cycle through different modes: Seven-color gradient Single-color breathing →Fixed color All off.
4. પ્રકાશની તીવ્રતાને સમાયોજિત કરવી:
   • Increase light brightness: Hold the “SELECT” and press the “Up” button on the D-Pad.
   • Decrease light brightness: Hold the “START” and press the “Down” button on the D-Pad.
   • There are six levels of light intensity: 20% brightness, 0-20%-40%-60%-80%-100%. The settings have memory and saving. functionality.
5. Eight-color Gradient Mode:
   • All lights are on with a seven-color gradient (left and right 3D lights).
   • The left and right 3D lights change cyclically through colors: Red, Grange, Yellow, Green, Cyan, Blue, Purple, White,.
6. Single-color Breathing Mode:
   • Eight types of colors: Red, Drange, Yellow, Green, Cyan, Blue, Purple, White.
   • Colors automatically change to the next in sequence every second. Press the START key and the RIGHT key to switch to the next color.
7. Fixed Color Mode:
   • Eight types of colors: Red, Drange, Yellow, Green, Cyan, Blue, Purple, White.
   • Colors automatically change to the next in sequence every second. Press the START key and the RIGHT key of the D-pad to switch to the next color.

Multi-Platform Wireless Connection Setup:

Android Wireless Connection Mode:
પગલું 1: Move the mode switch to the “Android” position.
પગલું 2: Press and hold the pairing button on the controller’s top for one second to enter Android Bluetooth Pairing mode;
LEDs 2 and 3 will flash rapidly.
પગલું 3: Enable Bluetooth on your Android device and select the detected controler: GAMEPAD.
પગલું 4: Upon successful connection, LEDs 2 and 3 will remain steady.

PC Steam Deck Wireless Connection Mode:

પગલું 1: Configure the mode switch to the “WIN PC” position.
પગલું 2: Press and hold the pairing button on the controller’s top for one second to activate Bluetooth pairing mode; LEDs 1 to 4 will flash rapidly.
પગલું 3: Enable Bluetooth on your PC/Steam Deck and choose the identified controller: Pro Controller.
પગલું 4: After a successful connection, LED 1 will stay solid.

IOS Wireless Connection Mode:

પગલું 1: Set the mode switch to the “IOS” position.
પગલું 2: Press and hold the pairing button on the controller’s top for one second to activate Bluetooth pairing mode; LEDs 1 and 2 will flash rapidly.
પગલું 3: Enable Bluetooth on your iOS device and select the detected controller: Xbox Wireless Controller.
પગલું 4: Upon successful connection, LEDs 1 and 2 will remain steady.

વાયર્ડ કનેક્શન:

પગલું 1: For a wired connection, switch the mode switch to the PC mode gear and connect the PC console using the included
Type-C data cable. LED1 LED3 will be on.
પગલું 2: Switch between modes by pressing and holding the Start Select keys for 3 seconds. In Dinput mode, LED1. LED4 will be on.
પગલું 3: Under PC mode, double-clicking the CAPTURE key can switch the function between the cross key and the left joystick.
નોંધ: The audio function only works in the WIRED Pro Controller mode and will not work in the wireless Pro Controller mode,

ચાર્જિંગ સૂચનાઓ:

• The controller can be charged using the console charger, the Dock, a 5V 2A power adapter, or USB power supplies with a USB Type-C to Type-A cable.
• While charging with the console, the channel LED light(s) will flash, and the lights will turn off when fully charged.
• If charging without the console, the four LED lights will flash, turning off when fully charged,
• Low battery is indicated by flashing channel LED light(s), prompting a charge to prevent the controller from turning off, Indicator Light Functionality of Charging Station:
• When the charging dock is powered on, the white indicator lights up briefly.
• During the gamepad charging process, the white light remains iluminated,
• Once the gamepad is fully charged, the white light switches off.
  
  

Calibrating the Control Sticks:

પગલું 1: હોમ બટન દબાવો.
પગલું 2: Navigate to System Settings > Controllers and Sensors > Calibrate Control Sticks.
પગલું 3: Press the stick you want to calibrate.
પગલું 4: નિયંત્રક કાર્યક્ષમતાને ચકાસવા માટે ઑન-સ્ક્રીન સૂચનાઓને અનુસરો.

Calibrating Motion Controls:

1. હોમ બટન દબાવો.
2. Navigate to System Settings > Controllers and Sensors > Calibrate Motion Controls > Calibrate the Controllers.
3. Place the controller on a horizontal plane.
4. Hold “SELECT(-)” or “START(+)” on the controller you want to calibrate.

મહેરબાની કરીને નોંધ કરો:

• For first-time use of the wireless controller, it is recommended to calibrate both the Controller Sticks and Motion Controls before usage.
• If calibration fails, press the “Y” button to restore settings and the “X” button to repeat the calibration steps.
• After calibration, power off the controller, then restart both the controller and console for the settings to take effect.

Calibration and Interchange Function:

• If the joystick is not centered or drifts during use, you can manually correct it.
• First, turn the trigger limit switch to the analog gear,
• Press the Turbo Start Home keys to enter calibration mode, LED1 LED3 and LED2 LED4 will flash alternately.
• Shake the left and right joysticks two or three times. Slowly press the trigger. Repeat this process two or three times.
• Press the Select key to exit calibration mode, completing the calibration process.

કાર્યક્ષમતા સૂચનાઓ:

3D Circular/Rectangular Switching:

• To switch between circular and rectangular modes, press L3 Capture key.
• The RGB lights around 3D will change between red and blue.
• Motor vibration prompts will indicate the mode switch.
• The default mode is circulac

ABXY Position Interchange:

• Press Capture A key to interchange the A and B buttons, and the X and Y buttons.
• The RGB lights around 3D will change between red and green..
• Motor vibration prompts will indicate the button swap.
• Memory adjustment is available for this function.

3D Dead Zone Conversion:

• Press START key + L3/R3 to toggle the dead zones.
• The indicator light will flash three times, accompanied by motor vibration prompts.
• You can turn off or on the left and right 30 dead zones with a 0% dead zone option.

ફેક્ટરી ડિફોલ્ટ્સને પુનર્સ્થાપિત કરો:

• Press and hold Select L3 R3 for 5 seconds to restore factory defaults.
• Turbo vibration, macro definition, lighting effects, and key swaps will reset to their default values.
• The motor will vibrate for an extended period to indicate the reset completion.

બેટરી કાર્યો:
ચાર્જિંગ:

• When the gamepad is off and charging, the decorative lights are turned off. LED1-LED4 flash slowly.
• When fully charged, the LED lights turn off.

બ Batટરી સ્તરનું પ્રદર્શન:

• While the gamepad is on, briefly press the Turbo and keys to display the battery level
• After 3 seconds, it returns to the current channel light status.
• Light 1: 1%-25% battery level
• Lights 1 and 2: 26%-50% battery level
• Lights 1, 2, and 3: 51%-75% battery level
• Lights 1, 2, 3, and 4: 76%-100% battery level

ઓછી બેટરી સ્થિતિ:

• જો લિથિયમ બેટરી વોલtage drops below 3,55V ± 0,1V, the current channel light flashes quickly to indicate low voltage.
• ભાગtage threshold can be adjusted as needed.

ઓછી બેટરી શટડાઉન:

• જો લિથિયમ બેટરી વોલtage falls below 3.35V±0.1V, the gamepad will automatically enter sleep mode.
• ભાગtage threshold can be adjusted according to requirements.

Firmware Update Instructions:

પગલું 1: તમારા મોબાઈલ એપ સ્ટોર પરથી “KeyLinker” એપ ડાઉનલોડ કરો.
પગલું 2: Press and hold the SYNC button on the controler until the indicators flash quickly.
પગલું 3: Enable Bluetooth on your mobile device and pair it with the controller named “KeyLinker BLE-XXXX”.
પગલું 4: Open the “KeyLinker” app and refresh it. Connect with the device “GAMEPAD” to access the app’s features.
Now you can now customize functions and upgrade the firmware of your controller through the app.
પગલું 5: Select “Update Device” from the app menu.
પગલું 6: If a new version is available, click “Update Now” and confirm by selecting “Yes” when the update prompt appears.
પગલું 7: The firmware will be successfully updated. Restart your device and the app.

નોંધ:

• Firmware updates are primarily to address occasional bugs.
• Only update if your controller experiences issues during use.
• There are no functional differences between firmware versions.
  

  ઉત્પાદન પર અથવા સૂચનાઓમાં આ પ્રતીકનો અર્થ એ છે કે તમારા ઇલેક્ટ્રિકલ અને ઇલેક્ટ્રોનિક સાધનોનો તેના જીવનના અંતમાં તમારા ઘરના કચરામાંથી અલગ રીતે નિકાલ કરવો જોઈએ. EU માં રિસાયક્લિંગ માટે અલગ સંગ્રહ સિસ્ટમો છે. વધુ માહિતી માટે કૃપા કરીને તમે જ્યાં ઉત્પાદન ખરીદ્યું છે તે સ્થાનિક સત્તાધિકારી અથવા તમારા રિટેલરનો સંપર્ક કરો.

પાવર ઇન્ટરનેશનલ AS,
PO Box 523, 1471 Lørenskog, Norway
પાવર નોર્જ:
https://www.power.no/kundeservice/
ટી: 21 00 40 00
નિષ્ણાત ડેનમાર્ક:
https://www.expert.dk/kundeservice/
ટી: 70 70 17 07
પાવર ડેનમાર્ક:
https://www.power.dk/kundeservice/
ટી: 70 33 80 80
પંકટ 1 ડેનમાર્ક:
https://www.punkti.dk/kundeservice/
ટી: 70 70 17 07
પાવર ફિનલેન્ડ:
https://www.powerfi/ટુકી/આસિયાકસ્પલવેલુ/
T: 0305 0305
પાવર સેવરેજ:
https://www.powerse/kundservice/T: 08 517 66 000

 

દસ્તાવેજો / સંસાધનો

CEPTER HORIZON Wireless Controller [પીડીએફ] વપરાશકર્તા માર્ગદર્શિકા 4894526096533, HORIZON Wireless Controller, HORIZON, Wireless Controller, Controller

સંદર્ભો

• વપરાશકર્તા માર્ગદર્શિકા