Cosmic Byte ECLIPSE TRI Mode Controller User Manual

Cosmic Byte ECLIPSE TRI Mode Controller

ઉત્પાદન સ્પષ્ટીકરણો

નોંધ: All specifications are for reference and may vary depending on usage and environment.

પેકેજ સામગ્રી

• Eclipse Controller × 1
• Replaceable D-Pad × 1
• 2.4G Receiver × 1
• USB Type-C Cable (1.5m) × 1
• વપરાશકર્તા માર્ગદર્શિકા × 1

હાઇલાઇટ્સ

Mode Switching Position: From left to right: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch)

ઓપરેશન સૂચનાઓ

HOME CB Indicator Light

• Blue – iOS and Android
• Orange – 2.4G Mode

પ્રથમ વખત જોડાણ

• 2.4G વાયરલેસ મોડ
  • Set the mode switch toggle to 2.4G (Middle).
  • USB રીસીવરને તમારા ઉપકરણમાં પ્લગ કરો.
  • While the controller is powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly. Once it turns solid and the controller vibrates briefly, the connection is successful.
• બ્લૂટૂથ મોડ
  • Set the mode switch toggle to Bluetooth (Left).
  • While powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly.
  • On your device (PC/Android/iOS), enable Bluetooth and select ‘Xbox Wireless Controller’.
  • When the logo light turns solid and the controller vibrates, the pairing is complete.
• વાયર્ડ મોડ
  • Connect the controller to your device using the included USB Type-C cable.
  • Wired mode activates automatically when connected.

પુનઃજોડાણ
To reconnect to the last paired device (with the same mode), short-press the Home button.

જોયસ્ટિક ગોઠવણ

• Dead Zone Toggle:
  • Press and hold Left and Right Stick (LS/RS) for 5 seconds to switch between 5% and 0% deadzone.
  • Controller will vibrate to confirm the change.
• Active Zone Shape Toggle:
  • Press and hold M + LS or RS for 5 seconds to toggle between 10% square zone and 0% circle zone.

 Turbo and Continuous Fire

• મેન્યુઅલ ટર્બો
  • Press M + A while holding the A button to enable manual turbo (continuous fire).
  • Logo light will flash red rapidly.
• ઓટો ટર્બો
  • Press M + A again to switch to auto turbo. Press again to cancel turbo.
  • A single press of A will now fire continuously.
• Clean all Turbo
  • Press M button twice and hold M for 5 secs, controller will vibrate & clean all Turbo settings.
• ટર્બો સ્પીડ એડજસ્ટમેન્ટ
  • Hold M + Right Stick Up/Down to increase or decrease turbo speed.
  • Vibration feedback indicates change.

ABXY Lighting Adjustment

• Press M + Right Stick Left and Right to adjust brightness.
• 4 Brightness Levels: 0% → 30% → 70% → 100%

કંપન તીવ્રતા ગોઠવણ

• Press and hold M + Right Stick Up to increase vibration intensity.
• Press and hold M + Right Stick Down to decrease.
• 4 Levels: 0% (off) → 30% → 70% → 100%

ABXY લેઆઉટ સ્વિચ

Use the layout switch on the front to toggle between XBOX-style and Alternate-style layouts.

Rapid Trigger Adjustment
Adjust LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.

માપાંકન

• લાકડી અને ટ્રિગર કેલિબ્રેશન
  • નિયંત્રક પર પાવર.
  • પકડી રાખો View + M + Menu for 3 seconds to enter calibration.
  • LED1 and LED3 will flash.
  • Rotate both sticks clockwise 3 full turns.
  • Fully press both triggers 3 times.
  • Switch triggers to short travel mode, then press them fully 3 more times.
  • દબાવો View બહાર નીકળવા માટે.
  • LED1 and LED3 will stay solid for 5 seconds before powering off.
• ગાયરોસ્કોપ કેલિબ્રેશન
  • કંટ્રોલરનો પાવર બંધ કરો અને તેને સપાટ સપાટી પર મૂકો.
  • પકડી રાખો View + A + B + Home to enter gyro calibration.
  • LED1 and LED2 will flash.
  • After 1 second, press Menu to complete calibration. LEDs will turn off.
  • Calibration must be performed in XBOX (ABXY) layout mode.

Macro Programming (M1/M2 Buttons)

• While connected, hold M + M1 or M2 for 3 seconds to enter programming mode.
• Press the desired button to assign (e.g., A, B, etc.).
• Press M1 or M2 again to save and exit.

નોંધ: If no button is selected, M1/M2 will be blank. Up to 21 Programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks

પાવર બંધ

• Hold the Home button for 5 seconds to power off.
• Auto power-off after 10 minutes of inactivity.

કંટ્રોલર રીસેટ
Use a small pin to press the Reset hole to restore factory settings.

 Joystick Force Adjustment (Roller-Based)
The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism. Follow the steps below to customize the joystick force according to your preference:

• Locate the joystick roller at the base of each analog stick.
• To increase joystick resistance, rotate the roller clockwise.
• To decrease joystick resistance, rotate the roller counter-clockwise.
• Make adjustments gradually and test after each rotation to find your preferred setting.

નોંધ: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).

બેટરી સૂચક માર્ગદર્શિકા

• ઓછી બેટરી: Logo light flashes red once every 10 minutes
• ચાર્જિંગ: Logo light breathes green
• સંપૂર્ણ ચાર્જ થયેલ: Logo light turns off

મોબાઇલ એપ ડાઉનલોડ કરો

Download and install the “Key Linker” App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.

વોરંટી

• The Eclipse Tri-Mode Controller carries a 1-year warranty against manufacturing defects only.
• Physical, water damage, and tampered ઉત્પાદનો વોરંટી હેઠળ આવરી લેવામાં આવતાં નથી.

Scan the QR Code to know the Warranty Claim Procedure.

આધાર વિગતો

• Customer Care Number: +91 7351615161 (Mon-Sat 10am to 6pm)
• WhatsApp Support: +91 7351615161
• ઈમેલ: cc@thecosmicbyte.com